|
|
|
Tecatron Textile |
Sewing Machine Thread Detector
|
| Model
: HS-9 |
| 
Sewing Machine Thread Detector HS-9 : The
Tecatron Piezo-Electric-Thread Stop Motion or Break detection System HS-9 can
be used for every thread or yarn quality, even for smooth nylon or steel or composite
fibres or wires, thanks to the very high sensitivity of the detector. |  |
APPLICATIONS : - Sewing-Machines
- Heatset machines
- Twisting machines
- Winding machines
- Prewinders
- Rowing machines
- Glassfiber reinforcement machines
- Sample warping machines
- Cable making machines (small
diameters)
| |  |
Dimensions Detector :
L 66 mm x B 35 mm x H 20 mm Input Voltage Controller
Unit : 24 V AC/DC Output Contact : relay
opened and closed - 5A max. current Two rubber Shock absorbers
dia. 15mm x L 15mm x M4 are included and mounted at a distance of 23 mm and at
12 mm distance from the detector bottom,
See Picture. | |
|
| | |
Weft Stop Motion Detector
with 4 eyelets
Model
: WSD - 4
|  | |
The Standard
WS-4 Yarn Motion Controller :
The Tecatron Piezo-Electric Weft Stop Motion
System detects every Yarn Break or Stop with a fast reaction time. Because this
Model is a low cost Model, no additional options like a Digital Control Time delay
or Single or Double yarn setting are included. See for this future Model XSD-800
with 8 eyelets.
| | | | | Sensitivity adjustment :
the adjustment of the Yarn motion detection sensitivity is easily adjustable with
a rotary knob at the frontside of the detector. Input Voltage controller
Unit : 24 V AC/DC Output Contact : relay
opened and closed - 5A max. current | | |
|
Programmable Weft Stop Motion Detector
with 8 eyelets
Model : XSD-800
|
 | |
Digital Yarn Control Time Settings :
The Tecatron Piezo-Electric Weft Stop Motion System detects every Yarn Break
or Stop over a programmable length, this to control the Yarn motion over the total
weft time. A digital extra time can be set after the end signal by the proximity
switch, to adjust the total control time.
Switch single-double
: each of the 8 eyelets can be switched into the single or double
control position. - Single: detect every unwanted extra yarn movement
into other eyelets from the selected Single eyelet group , for instance if extra
yarns are inserted by mistake.
- Double : By
switching eyelets into the double position, this eyelet group controls that always
2 eyelets are activated during the weaving cycle. If only 1 or more than 2 eyelets
are activated, the machine will be stopped automatically.
| 
| |
|
|
| |
Output Contact : relay
opened and closed - 5A max. current | | |
|
Piezo-Electric
Rod Detector
Model : HS9-X / HS9-X2
| |
MODEL HS9-X | | |  | | | MODEL HS9-X or HS9-X2 :
- The HS9-X
/X2 Rod Detector detects the movements of plastic-, paper-, textile,- or metal
tapes, foils, bands or strips into each material, to rapidly stop the machine.
- The detector
sensitivities are at the highest level.
- Depending
on the band or tape specification, speeds lower than 0.05m/min. are detectable.
- The detector
system uses the same technology as the HS9 detector, but is equipped with a piëzo-electric
friction sensitive metal rod.
- The rod
is standard made in a hollow or massive Stainless
Steel Material, with a
diameter of 15 mm .
- A special
surface wear protection of the rod, such as a DLC-diamant coating or other hard
coatings are available on demand.
- Cooling : Possibility to let pass cooling liquids
through the center of the rod, mainly , if very high tape or band speeds are increasing
the temperature of the Metal Rod above 80°C. ( 1/8" BSP Din 2999 INLET and OUTLET
Rod cooling connection )
- The metal
rod is earthed to discharge any electrostatic voltage, as a result
of the possible high speed frictions of the used materials against this detection
rod
- The rod
length is made in accordance with the application need.
|
| |
Input Voltage Controller
Unit : 24 V AC/DC Output Contact : relay
opened and closed - 5A max. current Dimensions Detectors
:
L 66 mm x B 35 mm x H 20 mm + Rod Length  |
MODEL HS9-X2 :
- Depending
on the rod length and loads used, and depending on the sensitivity, a double or
single Detection Element is installed.
- The
Detector configuration must be placed on the machine with additional shock absorbers
and mounted at the height of the horizontal aluminum connecting bar between the
two detector elements.
- The holes
for the mounting of the included shock absorbers are custom made, depending on
the specifications of the customer.
- The aluminum
connecting bar can be removed or changed, and fixed with the screws M4 DIN 912
placed at a distance of 23mm on both sides |
|
|
|
| WEFT THREAD Break or Stop Motion
Detector for Weaving Machines |
|
Model : HS9-XC
| | |  | | | Weft Thread Detector HS9-XC :
The Tecatron
Piezo-Electric-Thread Stop Motion or Break detection System HS9-XC can be used
for every Textile Weaving Machine.
The sensitivity of the detector can be easily
set on the detector itself.
This detector will use the same technology as of
the HS9 detector, but with less sensitivity in relation with the high speed level
of the weft thread movements of textile machines. |
| |
| |
Dimensions Detector :
L 66 mm x B 35 mm x H 20 mm Input Voltage Controller
Unit : 24 V AC/DC Output Contact : relay
opened and closed - 5A max. current Two rubber Shock absorbers
dia. 15mm x L 15mm x M4 are included and mounted at a distance of 23 mm and at
12 mm distance from the detector bottom,
See Picture. | | The
Tecatron website content
is subject to a
| TECATRON
electronics ® |
|
TEXTILE
PRODUCTSTEXTILE PRODUCTS: for all applications
TEXTILE PRODUCTS:
for Sewing Machines
TEXTILE PRODUCTS: for the textile industry
TEXTILE PRODUCTS:
for weaving machines |
| | | |
